• Benvenuti su RaspberryItaly!
Benvenuto ospite! Login Login con Facebook Registrati Login with Facebook


Valutazione discussione:
  • 0 voto(i) - 0 media
  • 1
  • 2
  • 3
  • 4
  • 5

[-]
Tags
lcd con xpt2046 problema 4 320x480 quot error server xorg fatal

PROBLEMA CON LCD 4" XPT2046 320X480 Xorg Fatal server error
#1
Ciao a tutti,

sul mio Raspberry PI3 avevo installato questo display LCD:

4INCH RPI LCD (A)
320x480 pixel
XPT2046 Touch Controller

comprato su sito cinese.

Funzionava correttamente ma un giorno ha iniziato a darmi un errore in quanto il Raspberry partiva solo in emergency mode, non sono riuscito a risolvere il problema: avevo scritto questo post

https://forum.raspberryitaly.com/showthr...8#pid17628

Ho reinstallato tutto ma non riesco più a far funzionare LCD da 4" (ho fatto l'errore di non segnarmi come l'avevo precedentemente installato)

Ora mi restituisce il seguente errore che vi posto nelle immmagini seguenti:

   

   

Per installarlo ho fatto questa proccedura:

Ho estratto questo file: LCD-show-160729.tar.gz in dotazione con l'LCD

- Copiato nel desktop
e tramite consolle:

cd LCD-show
chmod +x LCD4-show
./LCD4-show
riavvio e non mi parte più la GUI

come posso risolvere?
Risposta
#2
verifica se in boot/config.txt vi è una stringa tipo
Codice:
dtoverlay=ads7846
e toglila (il file lo puoi vedere anche estraendo la sd e inserendola in un lettore collegato al pc, oppure via SSH)
Risposta
#3
ciao,

grazie per la risposta...

il file config è così composto:


Codice:
# For more options and information see
# http://www.raspberrypi.org/documentation/configuration/config-txt.md
# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output
hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces
dtparam=i2c_arm=on
#dtparam=i2s=on
dtparam=spi=on
enable_uart=1
# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
dtparam=audio=on
dtoverlay=waveshare35a
dtoverlay=ads7846,cs=1,penirq=17,penirq_pull=2,speed=1000000,keep_vref_on=1,swapxy=0,pmax=255,xohms=60,xmin=200,xmax=3900,ymin=200,ymax=3900


ho provato eliminando tutta l'ultima riga:

Codice:
dtoverlay=ads7846,cs=1,penirq=17,penirq_pull=2,speed=1000000,keep_vref_on=1,swapxy=0,pmax=255,xohms=60,xmin=200,xmax=3900,ymin=200,ymax=3900

ma non parte ugualmente la GUI
Risposta
#4
questo è Xorg.0.log

Codice:
[    30.058]
X.Org X Server 1.20.0
X Protocol Version 11, Revision 0
[    30.064] Build Operating System: Linux 4.9.0-6-armmp-lpae armv7l Debian
[    30.067] Current Operating System: Linux kali 4.9.80-Re4son-v7+ #1 SMP Thu Apr 26 17:45:16 CDT 2018 armv7l
[    30.068] Kernel command line: 8250.nr_uarts=1 bcm2708_fb.fbwidth=640 bcm2708_fb.fbheight=480 bcm2708_fb.fbswap=1 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000  dwc_otg.lpm_enable=0 console=tty1 console=ttyS0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline rootwait fbcon=map:10 fbcon=font:ProFont6x11 logo.nologo
[    30.078] Build Date: 01 July 2018  05:07:24PM
[    30.080] xorg-server 2:1.20.0-3 (https://www.debian.org/support)
[    30.082] Current version of pixman: 0.34.0
[    30.085] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[    30.085] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    30.099] (==) Log file: "/var/log/Xorg.0.log", Time: Mon Aug  6 20:13:13 2018
[    30.102] (==) Using config directory: "/etc/X11/xorg.conf.d"
[    30.105] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[    30.107] (==) No Layout section.  Using the first Screen section.
[    30.107] (==) No screen section available. Using defaults.
[    30.107] (**) |-->Screen "Default Screen Section" (0)
[    30.107] (**) |   |-->Monitor "<default monitor>"
[    30.109] (==) No device specified for screen "Default Screen Section".
Using the first device section listed.
[    30.109] (**) |   |-->Device "Allwinner A10/A13 FBDEV"
[    30.109] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[    30.110] (==) Automatically adding devices
[    30.110] (==) Automatically enabling devices
[    30.110] (==) Automatically adding GPU devices
[    30.110] (==) Max clients allowed: 256, resource mask: 0x1fffff
[    30.110] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[    30.110] Entry deleted from font path.
[    30.110] (==) FontPath set to:
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/100dpi/:unscaled,
/usr/share/fonts/X11/75dpi/:unscaled,
/usr/share/fonts/X11/Type1,
/usr/share/fonts/X11/100dpi,
/usr/share/fonts/X11/75dpi,
built-ins
[    30.110] (==) ModulePath set to "/usr/lib/xorg/modules"
[    30.110] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[    30.110] (II) Loader magic: 0x596f78
[    30.110] (II) Module ABI versions:
[    30.110] X.Org ANSI C Emulation: 0.4
[    30.110] X.Org Video Driver: 24.0
[    30.110] X.Org XInput driver : 24.1
[    30.111] X.Org Server Extension : 10.0
[    30.115] (++) using VT number 1

[    30.125] (II) systemd-logind: took control of session /org/freedesktop/login1/session/c1
[    30.126] (II) no primary bus or device found
[    30.126] (II) LoadModule: "glx"
[    30.127] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[    30.153] (II) Module glx: vendor="X.Org Foundation"
[    30.153] compiled for 1.20.0, module version = 1.0.0
[    30.153] ABI class: X.Org Server Extension, version 10.0
[    30.153] (II) LoadModule: "fbturbo"
[    30.154] (WW) Warning, couldn't open module fbturbo
[    30.154] (EE) Failed to load module "fbturbo" (module does not exist, 0)
[    30.154] (EE) No drivers available.
[    30.154] (EE)
Fatal server error:
[    30.154] (EE) no screens found(EE)
[    30.155] (EE)
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
[    30.155] (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information.
[    30.155] (EE)
[    30.161] (EE) Server terminated with error (1). Closing log file.
Risposta
#5
ma con Raspbian, funziona?
Risposta
#6
no, non funziona neanche con Raspbian

quando lancio ./LCD4-show si riavvia e si blocca in partenza con questo messaggio di errore:
end Kernel panic . not syncing: VFS: unable to mount root fs on unknown-block(179,2)

inizio a pensare che sia andato l'LCD. Ha sempre funzionato bene ed inoltre quando collegato oltre al monitor tramite HDMI ho sempre il fulmine in alto a destra come se non bastasse l'alimentazione nonostante l'alimentatore sia quello in dotazione da 5v 2,5 A
Risposta
#7
Con Raspbian sono riuscito a farlo funzionare. A questo punto credo che il problema sia la versione di Kali. dove si trovano le versioni vecchie? Nel sito ufficiale solo l'ultima
Risposta
#8
Un piccolo aggiornamento, sono riuscito a far funzionare lo schermo da 4" con questa procedura:

cd /usr/local/src
wget -O re4son-kernel_current.tar.xz https://re4son-kernel.com/download/re4so...l-current/
tar -xJf re4son-kernel_current.tar.xz
cd re4son-kernel_4*
./install.sh
reboot

# Log in to install the nexmon drivers
cd /usr/local/src/re4son-kernel_4*
./install.sh -x

cd /usr/local/src/re4son-kernel_4*
./re4son-pi-tft-setup -u

./re4son-pi-tft-setup -t wave40 -d /root
Risposta
#9
Ciao a tutti!non volevo aprire un nuovo thread, perchè vedo che questo è l'unico in tutto il foro che descrive meglio la mia situazione. Anch'io ho scaricato la versione Sticky fingers kali, e ho seguito la procedura da te descritta qui sopra; in realtaà il mio display LCD è diverso, infatti è questo https://www.amazon.it/Yosoo-Raspberry-Po...B00VWZJ22E , tuttavia dovrebbe possedere lo stesso chipset, ho provato varie guide ma niente, in questo caso il sistema si stucca in fase di reboot. Avete qualche idea a riguardo? accetto qualunque suggerimento, vi premetto che sono totalmente nuovo al mondo raspberry
Raspberry Pi B+ / StickyFingers Kali Pi

Computer Principale: CPU AMD Ryzen 2600x, RAM 16 gb Gskill Tridentz, MOBO Asus Prime x470-PRO, GPU RX580 Special Edition, Alimentatore EVGA G3 650 watt, CASE Sharkoon TG5,HD 1 500gb kingston SSD 1+1 Barracuda Seagate 7200 rpm, OS Win 10, Kali linux


Cool La conoscenza è potere
Risposta
  


Vai al forum:


Navigazione: 3 Ospite(i)
Forum con nuovi Post
Forum senza nuovi post
Forum bloccato
Forum Redirect