• Benvenuti su RaspberryItaly!
Benvenuto ospite! Login Login con Facebook Registrati Login with Facebook


Valutazione discussione:
  • 0 voto(i) - 0 media
  • 1
  • 2
  • 3
  • 4
  • 5

[-]
Tags
hdmi output set rpi4 1080i50

RPi4 set output hdmi 1080i50
#1
Ciao a tutti,
Ho un problema nella configurazione hdmi del mio RaspberryPi 4.

Mi serve che l'output hdmi sia 1920x1080 i50ed ho provato a configurarlo tramite il file config.txt ( allegato in fondo).
Ho quindi impostato l'output in modalitàCEA20 (1080i 50Hz 16:9) che in teoria è la configurazione corretta. Nonostante ciò l'output video (rilevato dal monitor) rimane comunque 1920x1080p50. Tra l'altro utilizzando tvservice la configurazione risulta effettuata correttamente.

Ho provato anche a settarlo come configurazione personalizzata ma il risultato è lo stesso.
Grazie in anticipo per l'aiuto

Codice:
pi@RPi4-RXStreamBox:~ $ tvservice -s

state 0xa [HDMI CUSTOM RGB lim 16:9], 1920x1080 @ 50.00Hz, progressive



pi@RPi4-RXStreamBox:~ $ tvservice -m CEA

Group CEA has 1 modes:
 (prefer) mode 20: 1920x1080 @ 50Hz 16:9, clock:74MHz interlaced

# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details



# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1



# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan

disable_overscan=0



# uncomment the following to adjust overscan. Use positive numbers if console

# goes off screen, and negative if there is too much border

#overscan_left=16

#overscan_right=16

#overscan_top=16

#overscan_bottom=16



# uncomment to force a console size. By default it will be display's size minus

# overscan.

#framebuffer_width=1280

#framebuffer_height=720



# uncomment if hdmi display is not detected and composite is being output

hdmi_force_hotplug=1



# uncomment to force a specific HDMI mode (this will force VGA)



hdmi_force_mode=1

hdmi_ignore_edid=0xa5000080



hdmi_group=1

hdmi_mode=20

hdmi_drive=2



# uncomment to force a HDMI mode rather than DVI. This can make audio work in

# DMT (computer monitor) modes

#hdmi_drive=2



# uncomment to increase signal to HDMI, if you have interference, blanking, or

# no display

#config_hdmi_boost=4



# uncomment for composite PAL

#sdtv_mode=2



#uncomment to overclock the arm. 700 MHz is the default.

#arm_freq=800



# Uncomment some or all of these to enable the optional hardware interfaces

#dtparam=i2c_arm=on

#dtparam=i2s=on

#dtparam=spi=on



# Uncomment this to enable infrared communication.

#dtoverlay=gpio-ir,gpio_pin=17

#dtoverlay=gpio-ir-tx,gpio_pin=18



# Additional overlays and parameters are documented /boot/overlays/README



# Enable audio (loads snd_bcm2835)

dtparam=audio=on



[pi4]

# Enable DRM VC4 V3D driver on top of the dispmanx display stack

dtoverlay=vc4-fkms-v3d

max_framebuffers=2



#dtoverlay=vc4-fkms-v3d
#hdmi_enable_4kp60=1
Risposta
#2
ciao,
prima una domanda stupida: se il monitor aggancia una modalità p (progressiva) perchè vuoi usare una modalità i (interlacciata)?
E' vero che su un LCD la differenza è oramai impercettibile, ma mi ponevo la domanda.
Detto questo, prova a tgliere il # davati a hdmi safe = 1
altrimenti puoi usare il comando hdmi_edid_file per far leggere la tabella delle frequenze da un file nella partizione di boot, invece che dal monitor/televisore. Qui è spiegato come
Risposta
#3
(29/05/2020, 08:11)Zzed Ha scritto: ciao,
prima una domanda stupida: se il monitor aggancia una modalità p (progressiva) perchè vuoi usare una modalità i (interlacciata)?
E' vero che su un LCD la differenza è oramai impercettibile, ma mi ponevo la domanda.
Detto questo, prova a tgliere il # davati a hdmi safe = 1
altrimenti puoi usare il comando hdmi_edid_file per far leggere la tabella delle frequenze da un file nella partizione di boot, invece che dal monitor/televisore. Qui è spiegato come

Ciao e grazie per la risposta,
Il Raspberry va inserito all'interno di un network video per servizi di trasmissione televisiva, quindi purtroppo la modalità di uscita hdmi deve essere quella per garantire la compatibilità con il resto del network.

Provo le due alternative che mi hai proposto e vi aggiorno!
Grazie ancora
Risposta
#4
Ciao,
Attualmente ho settato il config.txt esclusivamente così (rimuovendo tutto il resto).

Codice:
hdmi_force_hotplug=1
hdmi_ignore_edid=0xa5000080
hdmi_drive=2
hdmi_group=1
hdmi_mode=20
disable_overscan=1


dtparam=audio=on

[pi4]
# Enable DRM VC4 V3D driver on top of the dispmanx display stack
dtoverlay=vc4-fkms-v3d
max_framebuffers=2

Ho notato che all'accensione del Rasp il sistema rileva correttamente la modalità i, ma dopo pochi secondi cambia in p. Continuo a capirci ben poco.

Ho anche provato ad inserire hdmi_safe=1 come prima riga, ma il risultato è sempre lo stesso.
Risposta
#5
a vedere qui è possibile che il pi 4 non supporti le risoluzioni interlacciate?
Risposta
  


Vai al forum:


Navigazione: 1 Ospite(i)
Forum con nuovi Post
Forum senza nuovi post
Forum bloccato
Forum Redirect